Referral service: we connect you with independent, vetted local foundation contractors who do the work. How it works & how we're paid

Guide · Updated Nov 16, 2026

Post-tension slab foundations: how they work, warning signs, and repair cautions

A post-tensioning tendon in an anchor blockout cut into a concrete slab
A post-tensioning tendon in an anchor blockout during a Virginia highway slab project (FHWA). Illustrative only; not a house foundation. Photo: Federal Highway Administration, Public domain.

If your San Antonio-area home was built in the last few decades, there's a good chance the slab under it is post-tensioned. The Foundation Performance Association says foundations of most new homes in southeast Texas are post-tensioned because it is the most economical method (FPA). That changes how you drill, how you remodel, and who you want doing repairs.

The story: the hole that almost got drilled

Picture this (a typical scenario, not a real customer). A homeowner plans to anchor a safe to the garage floor. The installer asks for the builder's foundation plan: post-tensioned slab. Ten minutes with a scanner shows a tendon running right under the planned anchor spot. The anchor moves a foot. Nothing dramatic happens, which is exactly the point.

How a post-tension slab works

Instead of only rebar, the slab holds high-strength steel strands in plastic sleeves. After the pour, the strands are tensioned with a hydraulic jack to compress the concrete so it bears load and resists cracking, and the force is transferred to the slab through anchors cast into the edges (JLC).

FactDetailSource
What carries the loadSteel tendons on about a 3- or 4-foot grid, centered in a roughly 5-inch slab (typical single-family)JLC
Interior stiffeningIntegral ribs (interior footings) about 12 feet apart in each directionJLC
When cables get stressedCheck records show stressing within 3 to 10 days of the pourFPA
How commonFoundations of most new homes in southeast TexasFPA
What damages tendonsCorrosion, accidental impact, brittle wire cracking, coring or drilling after constructionPTI

Sources: JLC (Journal of Light Construction), Q&A: Adding a Point Load to a Post-Tensioned Foundation (PDF) (a California structural engineer's answer; typical values, not a design spec); Foundation Performance Association, FPA-SC-06-0: Homebuyers' Guide for Foundation Evaluation (Rev. 0, Oct 10, 2005; PDF); Post-Tensioning Institute, PT Applications: Repair.

The one rule: never drill or cut blind

  • Tendons are under thousands of pounds of tension; cutting one weakens the foundation and is potentially hazardous (JLC).
  • Locate tendons first with a high-strength metal detector or digital scanner (JLC), and keep new openings away from edge anchors.
  • PTI lists coring and drilling after construction among the causes of tendon failure (PTI).
  • Plumbing repairs through a PT slab, like a slab leak repair, need the same care.

Warning signs on a post-tension slab

The symptoms of movement are the same as any slab: sticking doors, sloping floors, slab cracks and brick cracks. On a PT slab, also report rust stains or a bulge at the slab edge where tendon anchors sit, since PTI lists corrosion as a cause of tendon damage (PTI). Not sure if a crack matters? See settling vs foundation problems.

Post-tension slab repair: what to ask

  1. How will you locate tendons before drilling for piers or plumbing access?
  2. Is the cause soil moisture, a leak, or a tendon issue? (A hydrostatic plumbing test helps rule out leaks.)
  3. Do you recommend an engineer's review? Angi puts a structural report at about $550 on average ($350–$800) (Angi).
  4. What exactly does the warranty cover? See foundation repair warranties.

Angi lists concrete slab repairs at $350–$20,000 nationally (Angi). PTI says damaged PT structures can be evaluated and restored to original or greater strength (PTI). Compare methods in concrete foundation repair options and slab foundation repair.

Your offer: an inspection from someone who checks before drilling

LevelSATX Foundation Network matches you with one vetted, independent network partner for a free foundation inspection and a written quote if work is needed. Ask them the questions above. We are a referral service and do not perform repairs; partners pay us for referrals, and any company can apply to join the network.

Get my free inspection match

Want a real number for your home?

Calculators and guides give ranges. A free inspection from one vetted, independent local contractor gives you a written quote. No cost, no obligation.

Get my free inspection →

Or call (210) 796-7891.

Frequently asked questions

What is a post-tension slab?

A concrete slab reinforced with high-strength steel strands (tendons) in plastic sleeves. After the concrete is poured, the strands are pulled tight with a hydraulic jack to squeeze the concrete, which helps it carry load and resist cracking, as a structural engineer explains in JLC.

How do I know if my house has a post-tension slab?

Check your builder documents or foundation plans. The Foundation Performance Association's homebuyers' guide says most new homes in southeast Texas are built on post-tensioned slabs because it is the most economical method. The tendon anchors are cast into the slab edges.

Can I drill into a post-tension slab?

Not without locating the tendons first. A tendon is under thousands of pounds of tension; cutting one weakens the foundation and can be hazardous. JLC notes tendon locations can be found with a high-strength metal detector or digital scanner. Ask a qualified pro or engineer before cutting, coring or anchoring.

Can a post-tension slab be repaired?

Yes. The Post-Tensioning Institute says damaged PT structures can be evaluated and restored to their original or greater strength. Foundation movement on clay is usually addressed the same way as other slabs (drainage, moisture control, piers), by a contractor who knows how to work around tendons.

What does post-tension slab repair cost?

There is no separate national price for PT slabs. Angi lists concrete slab repairs at $350–$20,000 nationally, and a structural engineer's report averages about $550. LevelSATX Foundation Network can match you with one vetted network partner for a free inspection and written quote.

Keep reading

Sources cited on this page: Angi, How Much Does Foundation Repair Cost? (updated Oct 26, 2026); Angi, How Much Does Pier and Beam Foundation Repair Cost? (updated Sep 18, 2026); Foundation Performance Association, FPA-SC-06-0: Homebuyers' Guide for Foundation Evaluation (Rev. 0, Oct 10, 2005; PDF); JLC (Journal of Light Construction), Q&A: Adding a Point Load to a Post-Tensioned Foundation (PDF); Post-Tensioning Institute, PT Applications: Repair; Angi, How Much Does a Structural Engineer Cost to Hire? (2026 data, updated Oct 26, 2026); Texas Master Naturalist, Alamo Area Chapter: Bexar County Soils; Texas Dept. of Licensing & Regulation, Technical Bulletin IHB TB 10-01 (Foundations on Expansive Soils). Cost figures are national, not San Antonio quotes.

LevelSATX Foundation Network connects San Antonio homeowners and commercial property owners with vetted, independent foundation repair contractors. We don't perform repairs; participating contractors pay us for referrals. Any company can apply to join the network.

Get your free foundation inspection

4 quick taps. Free, no obligation.

Question 1 of 4

What are you noticing?
What's the property's ZIP code?

What kind of property is it?

When would you like someone to look?
Where should your match reach you?

Referral service: LevelSATX Foundation Network connects San Antonio homeowners and commercial property owners with vetted, independent foundation repair contractors. We don't perform repairs; participating contractors pay us for referrals. Any company can apply to join the network. We share your request with one matched contractor. Details

Get my free inspection → Call (210) 796-7891